MATERIAL SAFETY DATA SHEET MSDS-052
Prepared to OSHA, ACC, ANSI, WHMIS & 2001/58 EC Standards MSDS Revision: 1.0 MSDS Revision Date: 01/01/2005


1. PRODUCT IDENTIFICATION
1.1 Product Name:

NAIL ENVY SENSITIVE & PEELING
1.2 Chemical Name:
SOLVENT MIXTURE
1.3 Synonyms:
NA
1.4 Trade Names:
NT T121 ?? NT T126
1.5 Product Use:
COSMETIC USE ONLY
1.6 Manufacturer??s Name:
OPI PRODUCTS, INC.
1.7 Manufacturer??s Address:
13034 SATICOY STREET, NO. HOLLYWOOD, CA 91605 1.8 Emergency Phone:

CHEMTREC: (703) 527-3887
1.9 Business Phone:
(818) 759-2400


2. COMPOSITION & INGREDIENT INFORMATION
EXPOSURE LIMITS IN AIR (mg/m3)
ACGIH - ppm OSHA - ppm OTHE %
CHEMICAL NAME(S) CAS No. RTECS No. EINECS No. TLV STEL PEL STEL IDLH
ETHYL ACETATE 141-78-6 AH5425000 201-550-6 ?? 35.0 400 NE 400 NE 2000 400 TWA
BUTYL ACETATE 123-86-4 AF7350000 204-658-1 ?? 20.0 150 200 200 200 1700 150 TWA
NITROCELLULOSE 9004-70-0 QW0970000 NA ?? 10.0 (10) NE (10) NE NE
SD ALCOHOL 40B KQ6300000 200-578-6 ?? 10.0 1900 NA 1000 NA NA
64-17-5
SUCROSE ACETATE ISOBUTYRATE 126-13-6 WN6550000 204-771-6 ?? 10.0 NE NE NE NE NE
ETHYL TOSYLAMIDE NA NA ?? 10.0 NE NE NE NE NE
80-39-7
ISOPROPYL ALCOHOL 67-63-0 NT8050000 200-661-7 ?? 10.0 400 500 400 500 2000 400 TWA
ADIPIC ACID/NEOPENTYL
NA NA ?? 5.0 NE NE NE NE NE
GLYCOL/TRIMELLITIC ANHYDRIDE 28407-73-0
COPOLYME STYRENE ACRYLATES
NA NA ?? 3.0
9010-92-8 NE NE NE NE NE
COPOLYME TOSYLAMIDE/EPOXY RESIN 130353-62-7 NA NA ?? 3.0 NE NE NE NE NE
ETOCRYLENE 5232-99-5 ?? 1.0
NA NA NE NE NE NE NE
DIMETHICONE ?? 1.0
9006-65-9 NA NA NE NE NE NE NE
KUKUI (ALEURITES MOLUCCANA)
?? 1.0
8015-80-3 NA NA NE NE NE NE NE
NUT OIL
ASCORBIC ACID ?? 1.0
50-81-7 NA NA NE NE NE NE NE
TOCOPHERYL (VITAMIN E)
NA 231-710-0 ?? 1.0
7695-91-2 NE NE NE NE NE
ACETATE
ALOE BARBADENSIS (ALOE VERA)
NA 287-390-8 ?? 1.0
85507-69-3 NE NE NE NE NE
EXTRACT
HYDROLYZED WHEAT PROTEIN 70084-87-6 NA NA ?? 1.0 NE NE NE NE NE
CI 60725 (VIOLET #2) 81-48-1 CB7700000 201-353-5 ?? 1.0 NE NE NE NE NE
OTHER COMPONENTS PRESENT IN LESS THAN 1% CONCENTRATION BAL THE REMAINING COMPONENTS DO NOT CONTRIBUTE ANY
SIGNIFICANT ADDITIONAL HAZARDS
NA = Not Available; ND = Not Determined; NE = Not Established; C = Ceiling Limit; See Section 16 for Additional Definitions of Terms Used
NOTE: all WHMIS required information is included. It is located in appropriate sections based on the ANSI Z400.1-2003 format.
 MATERIAL SAFETY DATA SHEET MSDS-052
Prepared to OSHA, ACC, ANSI, WHMIS & 2001/58 EC Standards MSDS Revision: 1.0 MSDS Revision Date: 01/01/2005


3. HAZARD IDENTIFICATION
3.1 Hazard Identification:
Flammable liquid.
3.2 Routes of Entry: Inhalation: YES Absorption: YES Ingestion: YES
3.3 Effects of Exposure:
INGESTION: If product is swallowed, may cause nausea, vomiting and/or diarrhea and central nervous system depression.
SKIN & EYES: Irritating to the eyes. Symptoms of overexposure may include redness, itching, irritation and watering. May be
irritating to skin in some sensitive individuals, especially after prolonged and/or repeated contact.
INHALATION: Vapors of this product may be slightly irritating to the nose, throat and other tissues of the respiratory system.
Symptoms of overexposure can include coughing, wheezing, nasal congestion, and difficulty breathing. Inhalation of
vapors exceeding the levels listed in Section 2 (Composition and Ingredient Information) can cause central nervous
system depression (e.g., drowsiness, dizziness, headaches, nausea).
3.4 Symptoms of Overexposure:
Symptoms of skin overexposure in individuals may include redness, itching, and irritation of affected areas. Overexposure in eyes
may cause redness, itching and watering.
3.5 Acute Health Effects:
Mild to moderate irritation to eyes and skin near affected areas. Additionally, high concentrations of vapors can cause drowsiness,
dizziness, headaches and nausea.
3.6 Chronic Health Effects:
None known.
3.7 Target Organs:
Eyes, skin and respiratory system.


4. FIRST AID MEASURES
4.1 First Aid:
INGESTION: If ingested, do not induce vomiting. If product has been swallowed, drink plenty of water or milk IMMEDIATELY. If the
patient is vomiting, continue to offer water or milk. Never give water or milk to an unconscious person. Contact the
nearest Poison Control Center or local emergency number. Provide an estimate of the time at which the material was
ingested and the amount of the substance that was swallowed.
EYES: Splashes are not likely; however, if product gets in the eyes, flush with copious amounts of lukewarm water for at least
15 minutes. If irritation occurs, contact a physician.
SKIN: If irritation occurs and product is on the skin, rinse thoroughly with lukewarm water, followed by a thorough washing of
the effected area with soap and water. If irritation, redness or swelling persists, contact a physician immediately.
INHALATION: Remove victim to fresh air at once.

HEALTH 1
4.2 Medical Conditions Aggravated by Exposure:
None known.
FLAMMABILITY 3
REACTIVITY 0
PROTECTIVE EQUIPMENT A
EYES
 MATERIAL SAFETY DATA SHEET MSDS-052
Prepared to OSHA, ACC, ANSI, WHMIS & 2001/58 EC Standards MSDS Revision: 1.0 MSDS Revision Date: 01/01/2005


5. FIREFIGHTING MEASURES
5.1 Flashpoint & Method:
-4 ??C (24 ??F) estimated.
5.2 Autoignition Temperature:
NA
5.3 Flammability Limits: Lower Explosive Limit (LEL): NE Upper Explosive Limit (UEL): NE
5.4 Fire & Explosion Hazards:
WARNING: Flammable! Keep away from heat, lit cigarettes, sparks & open flame. Keep container closed.
5.5 Extinguishing Methods:
CO2, Halon, Dry Chemical, Foam
5.6 Firefighting Procedures:
This product is a Class IB flammable liquid. When involved in a fire, this product will ignite readily and
decompose to produce carbon oxides. Vapors of this product are heavier than air and may travel to a source of
ignition and flash back to a leaking or open container.
First responders should wear eye protection. Structural firefighters must wear SCBAs and full protective
equipment. Use a water spray or fog to reduce or direct vapors. Water may not be effective in actually
extinguishing a fire involving this product.



6. ACCIDENTAL RELEASE MEASURES
6.1 Spills:
Before cleaning any spill or leak, individuals involved in spill cleanup must wear appropriate Personal Protective Equipment.
For small spills (e.g., <1 gallon) wear appropriate personal protective equipment (e.g., goggles, gloves). Maximize ventilation (open
doors and windows) and secure all sources of ignition. Remove spilled material with absorbent material and place into appropriate
closed container(s) for disposal. Dispose of properly in accordance with local, state and federal regulations. Wash all affected areas
and outside of container with plenty of warm water and soap. Remove any contaminated clothing and wash thoroughly before
reuse.
For spills ?? 1 gallon, deny entry to all unprotected individuals. Dike and contain spill with inert material (e.g., sand or earth). Use ONLY
non-sparking tools for recovery and cleanup. Transfer liquid to containers for recovery or disposal and solid diking material to
separate containers for proper disposal. Remove contaminated clothing promptly and wash affected skin areas with soap and water.
Keep spills and cleaning runoffs out of municipal sewers and open bodies of water.


7. HANDLING & STORAGE INFORMATION
7.1 Work & Hygiene Practices:
Avoid prolonged contact with the product. Avoid breathing vapors of this product. Use in a well-ventilated location (e.g., local
exhaust ventilation, fans). After use, wash hands and exposed skin with soap and water. Do not eat, drink or smoke while handling
product.
7.2 Storage & Handling:
Keep this material away from heat, sparks and open flame. Open containers slowly on a stable surface. Keep container closed
tightly when not in use. Empty container may contain residual amounts of this product; therefore, empty containers should be
handled with care. Store containers in a cool, dry location, away from direct sunlight, other light sources, or sources of intense heat.
Store away from incompatible materials (see Section 10).
7.3 Special Precautions:
Open containers slowly on a stable surface. Keep container tightly closed when not in use. Empty containers may contain residual
amounts of this product; therefore, empty containers should be handled with care.
 MATERIAL SAFETY DATA SHEET MSDS-052
Prepared to OSHA, ACC, ANSI, WHMIS & 2001/58 EC Standards MSDS Revision: 1.0 MSDS Revision Date: 01/01/2005


8. EXPOSURE CONTROLS & PERSONAL PROTECTION
8.1 Ventilation & Engineering Controls:
When working with large quantities of product, provide adequate ventilation (e.g., local exhaust ventilation, fans). Ensure that an
eyewash station, sink or washbasin is available in case of exposure to eyes.
8.2 Respiratory Protection:
No special respiratory protection is required under typical circumstances of use or handling. If necessary, use only respiratory
protection authorized per U.S. OSHA's requirement in 29 CFR ??1910.134, or applicable U.S. state regulations, or the appropriate
standards of Canada, its provinces, E.C. member states, or Australia.
8.3 Eye Protection:
Depending on the use of this product, splash or safety glasses may be worn. If necessary, refer to U.S. OSHA 29 CFR ??1910.133,
Canadian standards, or the European Standard EN166.
8.4 Hand Protection:
If anticipated that prolonged & repeated skin contact will occur during use of this product, wear latex or rubber gloves for routine
industrial use. If necessary, refer to U.S. OSHA 29 CFR ??1910.138, the appropriate standards of Canada, of the E.C. member states.
8.5 Body Protection:
No special body protection is required under typical circumstances of use and handling. If necessary, refer to appropriate standards
of Canada, the E.C. member states, or U.S. OSHA.


9. PHYSICAL & CHEMICAL PROPERTIES
9.1 Density: 0.96
9.2 Boiling Point: 171 - 640??F
9.3 Melting Point: NE
9.4 Evaporation Rate: NA
9.5 Vapor Pressure: NA
9.6 Molecular Weight: NE
9.7 Appearance & Color: Viscous liquid, various colors
9.8 Odor Threshold: N 9.9 Solubility: Insoluble
9.10 pH NA
9.11 Viscosity: > 1200 cPs
9.12 Other Information: NA


10. STABILITY & REACTIVITY
10.1 Stability:
Stable under ambient conditions when stored properly (see Section 7, Storage and Handling).
10.2 Hazardous Decomposition Products:
If exposed to extremely high temperatures, the products of thermal decomposition may include irritating vapors and carbon oxide
gases (e.g., CO, CO2).
10.3 Hazardous Polymerization:
May occur, if exposed to extremely high temperatures.
10.4 Conditions to Avoid:
This product is incompatible with strong oxidizers (e.g., peroxides, superoxides), strong acids (e.g., hydrochloric or muriatic acids), or
strong bases (e.g., lye, potassium hydroxide).
10.5 Incompatible Substances:
None known.
 MATERIAL SAFETY DATA SHEET MSDS-052
Prepared to OSHA, ACC, ANSI, WHMIS & 2001/58 EC Standards MSDS Revision: 1.0 MSDS Revision Date: 01/01/2005


11. TOXICOLOGICAL INFORMATION
11.1 Toxicity Data:
This product has NOT been tested on animals to obtain toxicology data. There are toxicology data for the components of the
product, which are found in scientific literature. These data have not been presented in this document.
11.2 Acute Toxicity:
See Section 3.5
11.3 Chronic Toxicity:
See Section 3.6
11.4 Suspected Carcinogen:
This product contains Isopropyl Alcohol, which is not carcinogenic to humans but is listed as a Group 3 carcinogen by the IARC.
11.5 Reproductive Toxicity:
This product is not reported to cause reproductive toxicity in humans.
Mutagenicity:
This product is not reported to produce mutagenic effects in humans.
Embryotoxicity:
This product is not reported to produce embryotoxic effects in humans.
Teratogenicity:
This product is not reported to cause teratogenic effects in humans.
Reproductive Toxicity:
This product is not reported to cause reproductive effects in humans.
11.6 Irritancy of Product:
See Section 3.3
11.7 Biological Exposure Indices:
NE
11.8 Physician Recommendations:
Treat symptomatically.


12. ECOLOGICAL INFORMATION
12.1 Environmental Stability:
The components of this product will slowly degrade over time into a variety of organic compounds. Specific environmental data
available for the components of this product are as follows:
Ethyl Acetate: KOC = 0.73. Water solubility: 64,000 mg/l. Bioconcentration Factor = 4-14. Bioconcentration is not anticipated to be
significant. This compound can be removed from contaminated environments from volatilization, and biodegradation. This
compound??s half-life in water is 6.1 hours.
Butyl Acetate: KOC = 1.82. Water solubility: 120 parts H2O at 25??C (77??F). Bioconcentration Factor = 4-14. Bioconcentration is not
anticipated to be significant. This compound can be removed from contaminated environments from volatilization, and
biodegradation. This compound??s half-life in water is 6.1 hours.
12.2 Effects on Plants & Animals:
There are no specific data available for this product.
12.3 Effects on Aquatic Life:
There are no specific data available for this product; however, very large releases of this product may be harmful or fatal to
overexposed aquatic life.


13. DISPOSAL CONSIDERATIONS
13.1 Waste Disposal:
Waste disposal must be in accordance with appropriate Federal, state, and local regulations.
13.2 Special Considerations:
U.S. EPA WASTE NUMBER: D001 (characteristic - ignitable)
 MATERIAL SAFETY DATA SHEET MSDS-052
Prepared to OSHA, ACC, ANSI, WHMIS & 2001/58 EC Standards MSDS Revision: 1.0 MSDS Revision Date: 01/01/2005


14. TRANSPORTATION INFORMATION
The basic description (proper shipping name, hazard class & division, ID Number, packing group) is shown for each mode of transportation.
Additional descriptive information may be required by 49 CFR, IATA/ICAO, IMDG and the CTDGR.
14.1 49 CFR (GND):
CONSUMER COMMODITY, ORM-D (?? 1.0 L)
UN1263, PAINT, 3, II (> 1.0 L)
14.2 IATA (AIR):
CONSUMER COMMODITY, 9, ID8000 (?? 0.5 L)
UN1263, PAINT, 3, II (> 0.5 L)
14.3 IMDG (OCN):
UN1263, PAINT, 3, II, LTD QTY (?? 1.0 L)
UN1263, PAINT, 3, II (> 1.0 L)
14.4 TDGR (Canadian GND):
MARK PACKAGE "LIMITED QUANTITY" or "QUANTIT?? LIMIT??E" or "LTD QTY" or "QUANT LT??E" (?? 1.0 L)
UN1263, PAINT, 3, II (> 1.0 L)
14.5 ADR/RID (EU):
UN1263, PAINT, 3, II, ADR, LTD QTY (?? 1.0 L)


15. REGULATORY INFORMATION
15.1 SARA Reporting Requirements:
SARA 304 (40 CFR Table 302.4) ?? Butyl Acetate, Ethyl Acetate
15.2 SARA Threshold Planning Quantity:
There are no specific Threshold Planning Quantities for the components of this product.
15.3 TSCA Inventory Status:
The components of this product are listed on the TSCA Inventory.
15.4 CERCLA Reportable Quantity (RQ):
Butyl Acetate: 5000 lbs.; Ethyl Acetate: 5000 lbs.; Toluene: 1000 lbs.; Dibutyl Phthalate: 10 lbs.
15.5 Other Federal Requirements:
This product complies with the appropriate sections of the Food and Drug Administration??s 21 CFR subchapter G (Cosmetics).
15.6 Other Canadian Regulations:
This product has been classified according to the hazard criteria of the CPR and the MSDS contains all of
the information required by the CPR. The components of this product are listed on the DSL/NDSL. None
of the components of this product are listed on the Priorities Substances List. Class B2 Flammable Liquid.
15.7 State Regulatory Information:
Toluene, n-Butyl Acetate, Ethyl Acetate, and Isopropyl Alcohol are covered under specific state criteria. Components of this product
are not listed on the California Proposition 65 lists or they are exempt from the requirements.
15.8 67/548/EEC (European Union) Requirements:

The primary component of this product is not listed in Annex I of EU Directive 67/548/EEC:
Ethyl Acetate: Flammable (F). R: 11-36/37/38 ?? Highly flammable. Irritating to eyes, respiratory system
and skin. S: 2-16-23-29-33 ?? Keep out of the reach of children. Keep away from sources of ignition - No
smoking. Do not breathe gas, fumes, vapor or spray. Do not empty into drains. Take precautionary
measures against static discharges.
Butyl Acetate: Flammable (F). R: Flammable. S: 9-16-33 - Keep container in a well-ventilated place.
Keep away from sources of ignition - No smoking. Take precautionary measures against static
discharges.
 MATERIAL SAFETY DATA SHEET MSDS-052
Prepared to OSHA, ACC, ANSI, WHMIS & 2001/58 EC Standards MSDS Revision: 1.0 MSDS Revision Date: 01/01/2005


16. OTHER INFORMATION
16.1 Other Information:
EXTREMELY FLAMMABLE! Keep away from heat or flame. Use only as directed. Avoid eye contact. If contact occurs, flush eye
thoroughly with running water. Use only in a well-ventilated area. If redness or other signs of adverse reaction occur, discontinue use
immediately. Keep container closed. Store in a cool place. KEEP OUT OF REACH OF CHILDREN.
16.2 Terms & Definitions:
See page 7 of this MSDS.
16.3 Disclaimer:
This Material Safety Data Sheet is offered pursuant to OSHA??s Hazard Communication Standard, 29 CFR ??1910.1200. Other
government regulations must be reviewed for applicability to this product. To the best of ShipMate's & OPI Products?? knowledge, the
information contained herein is reliable and accurate as of this date; however, accuracy, suitability or completeness are not
guaranteed and no warranties of any type, either expressed or implied, are provided. The information contained herein relates only
to the specific product(s). If this product(s) is combined with other materials, all component properties must be considered. Data
may be changed from time to time. Be sure to consult the latest edition.
16.4 Prepared for:
OPI Products, Inc.
13034 Saticoy Street
No. Hollywood, CA 91605 (818) 759-2400 phone
(818) 759-5770 fax
http://www.opi.com/
16.5 Prepared by:
ShipMate, Inc.
18436 Hawthorne Boulevard, Suite 201
Torrance, CA 90504
310-360-3700 phone
310-360-5700 fax
http://www.shipmate.com/
 MATERIAL SAFETY DATA SHEET MSDS-052
Prepared to OSHA, ACC, ANSI, WHMIS & 2001/58 EC Standards MSDS Revision: 1.0 MSDS Revision Date: 01/01/2005
DEFINITION OF TERMS
A large number of abbreviations and acronyms appear on a MSDS. Some of these that are commonly used include the following:

GENERAL INFORMATION: NATIONAL FIRE PROTECTION ASSOCIATION: NFPA

CAS No. Chemical Abstract Service Number FLAMMABILITY LIMITS IN AIR:

EXPOSURE LIMITS IN AIR: Autoignition Minimum temperature required to initiate combustion
Temperature in air with no other source of ignition
ACGIH American Conference on Governmental Industrial Hygienists
LEL Lower Explosive Limit - lowest percent of vapor in air, by
TLV Threshold Limit Value
volume, that will explode or ignite in the presence of
OSHA U.S. Occupational Safety and Health Administration
an ignition source
PEL Permissible Exposure Limit
UEL Upper Explosive Limit - highest percent of vapor in air,
IDLH Immediately Dangerous to Life and Health by volume, that will explode or ignite in the presence of
an ignition source
FIRST AID MEASURES:

HAZARD RATINGS:
CPR Cardiopulmonary resuscitation - method in which a person
whose heart has stopped receives manual chest
0 Minimal Hazard
compressions and breathing to circulate blood and provide
oxygen to the body. 1 Slight Hazard
2 Moderate Hazard
FLAMMABILITY
HMIS?

HAZARDOUS MATERIALS IDENTIFICATION 3 Severe Hazard REACTIVITY
SYSTEM: HMIS
4 Extreme Hazard
ACD Acidic
HEALTH
HEALTH, FLAMMABILITY & REACTIVITY RATINGS:
ALK Alkaline
0 Minimal Hazard COR Corrosive
FLAMMABILITY
1 Slight Hazard W Use No Water
2 Moderate Hazard SPECIAL
OX Oxidizer
REACTIVITY HEALTH
PRECAUTIONS
3 Severe Hazard
4 Extreme Hazard PERSONAL PROTECTION TOXICOLOGICAL INFORMATION:
NCCHL44T ? NPCA Printed by Labelmaster, A, American Labelmark Co., Chicago, IL 60646 (800) 621-5808



PERSONAL PROTECTION RATINGS:
LD50 Lethal Dose (solids & liquids) which kills 50% of the
exposed animals s
A G LC50 Lethal concentration (gases) which kills 50% of the
exposed animal
ppm Concentration expressed in parts of material per
B H
million parts
TDlo Lowest dose to cause a symptom
C I TCLo Lowest concentration to cause a symptom
TDlo, LDlo, & LDo or Lowest dose (or concentration) to cause lethal or
D J TC, TCo, LClo, & LCo toxic effects
IARC International Agency for Research on Cancer
NTP National Toxicology Program
E K RTECS Registry of Toxic Effects of Chemical Substances
BCF Bioconcentration Factor
Consult your supervisor or S.O.P. for
F X TLm Median threshold limit
special handling directions.
log KOW or log KOC Coefficient of Oil/Water Distribution

REGULATORY INFORMATION:
Face Shield &
Safety Glasses Splash Goggles Gloves
Eye Protection WHMIS Canadian Workplace Hazardous Material Information System
DOT U.S. Department of Transportation
TC Transport Canada
EPA U.S. Environmental Protection Agency
Boots Dust Respirator
Synthetic Apron Full Suit
DSL Canadian Domestic Substance List
NDSL Canadian Non-Domestic Substance List
PSL Canadian Priority Substances List
Full Face
Dust & Vapor Airline Hood/Mask
Vapor Respirator Respirator
Respirator or SCBA TSCA U.S. Toxic Substance Control Act
EU European Union (European Union Directive 67/548/EEC)
Note: the dotted circle indicates that this respiratory protective
equipment is required for high concentrations or for large
EC INFORMATION:
volume spills or releases of product.

OTHER STANDARD ABBREVIATIONS:
NA Not Available
NR No Results
NE Not Established
C E F N O T+ Xi Xn
ND Not Determined
ML Maximum Limit Corrosive Explosive Flammable Harmful Oxidizing Toxic Irritant Harmful
SCBA Self-Contained Breathing Apparatus


SODIUM STYRENE/ACRYLATES COPOLYMER