MATERIALS SAFETY DATA SHEET
Product Identification: PRE-FILLED DYE TESTER ?? FLUORESCENT FT601
REFILL BOTTLE OF DYE ?? FLUORESCENT FD601
Product Description: LEAK LOCATING DYE

I. PRODUCT INFORMATION
Producer??s Name: Anderson Manufacturing Company, Inc. Date Prepared: 9/1/97
Address: 2885 Country Drive #190 Emergency Tel. # 800/424-9300 (CHEMTREC)
St. Paul, MN 55117 Info Tel. # 651/484-1316
Contact: Lance Anderson

II. INGREDIENTS/IDENTITY INFORMATION
Ingredients Cas#
Aqueous Solutions of Di Sodium Fluorescein 6417-85-2
Mixture Contains:
Fluorescein 2321-07-5
Sodium Sulfate 7757-83-7
Sodium Hydroxide 1310-73-2

SARA: Product does not contain any chemical(s) subje ct to reporting requirements of
SARA Title III Section 313.
TSCA: Product listed in compliance with TSCA
DSL: Listed

HMIS Rating Health: 2 Flammability: 0
Reactivity: 0 Protection: H

III. PHYSICAL/CHEMICAL CHARACTERISTICS

Boiling Point: N/A
Solubility in water: Soluble
Specific Gravity (H2O = 1): 10.6 LBS per gallon
% Volatiles (by volume): N/A
PH: 8.6-9.0 (Diluted 1:1 with water)
Appearance and Odor: Brown Aqueous Liquid

IV. FIRE AND EXPLOSION HAZARD DATA

Flash Point: N/A
Flammable Limits: N/A
Extinguishing Media: Waterfog, CO2, Dry Chemical
Special Fire Fighting Procedures: None
Flammable and Explosion Hazard: N/A
Unusual Hazards: None Expected
V. REACTIVITY DATA
Stability: Stable X
Unstable
Conditions to Avoid: None Known
Incompatibility (Materials to avoid): None Known
Hazardous Decomposition or By-products: Combustion will produce Carbon Dioxide and
may produce Carbon Monoxide
Hazardous Polymerization: Will not occur

VI. HEALTH HAZARD DATA
Carcinogen: No citation found
Signs/Symptoms of
overexposure: Liquid contact may irritate eyes and skin. Solution is alkaline
Emergency and First-Aide
Procedures: Inhalation: N/A Ingestion: Seek Medical Attention
Skin Contact: Wash with soap and water. Eye Contact: Flush
with water for 15 minutes ?? consult a physician.

VII. PRECAUTIONS FOR SAFE HANDLING AND USE
Step to be take in case material
is released or spilled: Use an absorbent to solidify materia l, sweep or shovel spills in to
approved waste disposal container.
Waste Disposal Method: Dispose of spilled product, empty containers and unused product
according to federal, state and local laws.
Precautions to take in
handling and storing: Avoid eye contact and excessive skin contact.
Other Precautions: Wash thoroughly from skin after handling. Avoid ingestion.

VII. CONTROL MEASURE
Respiratory Protection: Normally none used
Ventilation: Local Exhaust? Recommended Mechanical? N/A Special? N/A
Protective Gloves: Wear impervious gloves for prolonged use.
Eye Protection: Wear splash-proof chemical goggles or face shield if splashing hazards exist.
Other Protective Clothing
or Equipment: Normal work clothes to cover skin.



The information contained herein is based on data considered accurate. However, no warranty is expressed or
implied regarding the accuracy of these data or the results to be obtained from the use thereof.

Anderson Manufacturing Company assumes no responsibility for injury to vendee or third persons proximately
cause by the material if reasonable safety procedures are not adhered to as stipulated on the data sheet.
Additionally, Anderson Manufacturing Company assumes no responsibility for injury to vendee or third person
proximately caused by abnormal use of the material even if reasonable safety procedures are followed.
Furthermore, vendee assumes the risk in his/her use of the material.


URANINE K