DoALL Cutting Fluids
1228-H Harding Avenue
Des Plaines, IL 60016
Phone: 847/803-7262 ?? Fax: 847/803-1447


MATERIAL SAFETY DATA SHEET
==============================================================================
MS203 Bright Edge?? 150 ==============================================================================

PRODUCT NAME: Bright Edge?? 150
PRODUCT CLASS: CUTTING AND GRINDING OIL

=== SECTION I MANUFACTURER IDENTIFICATION ==============

MANUFACTURER'S NAME: DoALL COMPANY
ADDRESS: 254 No. Laurel Ave. Des Plaines, IL 60016.
EMERGENCY PHONE: (800) 535-5053 (INFOTRAC)
INFORMATION: (847) 803-7262
REVISION DATE: April 7, 2004

=== SECTION II HAZARDOUS INGREDIENTS IDENTIFICATION ==============

OCCUPATIONAL EXPOSURE LIMITS

INGREDIENTS: CAS #: OSHA PEL: ACGIH TLV: PERCENT:

Severely Hydro-
treated Naphthenic
Oil 64742-52-5 5mg/cu.m. 5mg/cu.m. 92.0

ALL THE REST OF THE INGREDIENTS IN THIS PRODUCT, AS LISTE BELOW, ARE NOT CONSIDERED HAZARDOUS UNDER THE LAW.

Chlorinated Fatty
Ester 68440-29-9 --- --- 1.0-4.0

Lard Oil 8016-28-2 --- --- 1.0-5.0

=== SECTION III PHYSICAL DATA ==============

Boiling Point: N Specific Gravity: 0.920 (Water = 1)
Vapor Pressure: N Melting Point: NA
Vapor Density: >1 (air = 1)
Evaporation Rate: ND (BuAc = 1)
Solubility in Water: Insoluble
pH: NA
Appearance: Amber Liquid
Odor: Oily

=== SECTION IV FIRE AND EXPLOSION DATA ==============

300 ??F COC.
FLASH POINT:
EXTINGUISHING MEDIA: Carbon Dioxide, Foam, or Dry Chemical.
FIRE FIGHTING PROCEDURES: Water stream or spray, to cool containers to prevent vapor formation and
ignition, may spread fire. Fog nozzles are preferred if water is used. Wear
SCBA gear in fire area.
UNUSUAL FIRE AN EXPLOSION HAZARDS: Oxides of Carbon, and Hydrogen Chloride.

==============================================================================
MS203 Bright Edge?? 150 ==============================================================================

=== SECTION V HEALTH HAZARD DATA ==============

ROUTES OF EXPOSURE AND EFFECTS OF OVER-EXPOSURE:

INHALATION: Minor breathing Difficulty.
EYE CONTACT: Minor Irritation.
SKIN CONTACT: Minor Irritation.
SKIN ABSORPTION: Not expected to occur.
INGESTION: Nausea, and/or Diarrhea.

CARCINOGENICITY:
LISTED BY NTP: No
LISTED BY IARC: No
LISTED BY OSHA: No

EMERGENCY FIRST AID PROCEDURES:
INHALATION: Remove person to fresh air. Get Medical attention.
EYE CONTACT: Flush with water for 15 minutes. If irritation persists, get Medical attention.
SKIN CONTACT: Wash exposed area with mild soap and warm water only. Do not use harsh soap or
solvent.
SKIN ABSORPTION: Get Medical attention.
INGESTION: Do not Induce vomiting. Keep person warm and quiet. Get Medical attention.

=== SECTION VI REACTIVITY DATA ==============

STABILITY: Stable.
INCOMPATIBILITY: Strong Oxidizers.
HAZARDOUS DECOMPOSITION PRODUCTS: Oxides of Carbon, and Hydrogen.
HAZARDOUS POLYMERIZATION: Will not occur.

=== SECTION VII HANDLING PRECAUTIONS ==============

IN CASE OF ACCIDENTAL RELEASE:
SMALL SPILLS: Use absorbent material.
LARGE SPILLS: Dike and pump into drums.
RESIDUE: Mop with soap and water.
WASTE DISPOSAL METHOD: Treat as an oily waste and dispose of in accordance with local, state, and federal
regulations.
STORAGE: Store dry in a closed container in a cool place away from any fire source.
OTHER PRECAUTIONS: Avoid Breathing MIST.

=== SECTION VIII PROTECTIVE MEASURES ==============

VENTILATION: General mechanical ventilation should be adequate. If misting occurs, provide local
ventilation
PROTECTIVE GLOVES: The use of NEOPRENE gloves or barrier cream that are impermeable to oil is
recommended.
EYE PROTECTION: Safety goggles or face shield are recommended.
OTHER PROTECTION: An emergency shower and eyewash should be available in the work area. Practice
reasonable personal hygiene. Wash exposed skin with mild soap and warm water only.
Oil-soaked clothing should be changed promptly and laundered before re-wearing.

==============================================================================
MS203 Bright Edge?? 150 ==============================================================================

=== SECTION IX REGULATION COMPLIANCE INFORMATION ==============

CAA: Contains no ozone depleting substance.
DOT: Not classified as hazardous.
RCRA: As received, not a hazardous waste material.
SARA:
TSCA: All ingredients are registered.
VOC:

=== SECTION X HMIS ==============

HEALTH: 2
FLAMMABILITY: 1
REACTIVITY: 1

==============================================================================




==============================================================================

Abbreviations and Symbols used in this MSDS:

NA Not Applicable < - Less Than
ND Not Determined > - Greater Than
BuAc Butyl Acetate

==============================================================================

Data in this MSDS is believed to be correct and reliable. However, The DoALL Co. does not assume
responsibility for it, or any recommendations contained in it, inasmuch as conditions and methods of use
are beyond our control. Further, we make no warranty, expressed or implied, of any kind regarding this
product or its use, and purchaser assumes all risks of use or handling either in accordance with directions
or not.

The information contained within this document is property of DoALL Cutting Fluids. Alteration to this document
in any form is against the law. While the information released from DoALL Cutting Fluids is accurate and up to
date, we cannot protect from unlawful editing and changing of the information. We cannot guarantee any
information unless it is received directly from DoALL Cutting Fluids. We accept no responsibility for what
happens to this information once it leaves our offices. Please only trust information received directly from DoALL.

==============================================================================


Fatty acids, tallow, Me esters, chlorinated